Products

Thermistor of resistance- 10K (5 pcs)

Robokorda — Mon, 05 Sep 2022 10:05:29 +0000

10K Ohm NTC Thermistor This Negative Temperature Coefficient (NTC) Thermistor varies in resistance according to temperature. It is a simple way to measure air temperature or the temperature of an adjacent device or surface.

Breadboard – 840 Points Solderless

Robokorda — Mon, 05 Sep 2022 09:58:16 +0000

A GL-12 840 Points Solderless Breadboard is an invaluable tool for experimenting with circuit designs . No soldering is required so it is easy to change connections and replace components.

Piezoelectric 3-12 Volt Buzzer

Robokorda — Mon, 05 Sep 2022 09:48:13 +0000

This is a general purpose continuous Piezo Electric Buzzer Alarm. It works between 3 to 12 V. It has two mounting holes and can be easily mounted to a flat surface.

20cm Male to Female Breadboard Jumber Wire ( 40pcs)

Robokorda — Mon, 05 Sep 2022 09:04:08 +0000

MR-EC-1002

20cm Male to Male Breadboard Jumber Wire ( 40pcs)

Robokorda — Mon, 05 Sep 2022 08:59:17 +0000

MR-EC-1001
This is Male to Male Jumper Wires (20cm) – 40 Pieces pack. A very Flexible and easily detachable cable to the no. of wires according to your requirement. It has 1Pin male to the 1pin male header with both ends.

ADXL345 GESTURE SENSOR

Robokorda — Mon, 05 Sep 2022 08:30:27 +0000

MR-S-1010
Digital Output: SPI / I2C
Low Power Consumption
Compact Accelemotor / inclinometer
5V/3.3V input support.
PCB Board Size: 28mm x 14 mm
lower pressure drop than the 1117 Onboard RT9161 chip power
ideal for noisy power environment

ADXL345 is a Breakout board for the Analog Device’s ADXL345 triple axis accelerometer. The module is populated with MOSFET based Voltage level conversion circuitry to enable you to interface different type of microcontrollers (3V3 & 5V).

LM 35 Heat Sensor

Robokorda — Mon, 05 Sep 2022 08:24:42 +0000

MR-S-1009
Calibrated directly in Degree Celsius (Centigrade)
Linear at 10.0 mV/°C scale factor
0.5°C accuracy guarantee-able (at a25°C)
Suitable for remote applications
Low cost due to wafer-level trimming
Operates from 4 to 30 volts
Less than 60 mA current drain
Low self-heating, 0.08°C in still air
Non-linearity only 0.25°C typical
Low impedance output, 0.1Ωfor 1 mA load

The LM35 series are precision integrated-circuit temperature sensors, whose output voltage is linearly proportional to the Celsius (Centigrade) temperature.

IR Module

Robokorda — Mon, 05 Sep 2022 08:19:41 +0000

MR-S-1008
5VDC Operating voltage
I/O pins are 5V and 3.3V compliant
Range: Up to 20cm
Adjustable Sensing range
Built-in Ambient Light Sensor
20mA supply current
Mounting hole”

The IR Sensor module has great adaptive capability of the ambient light, having a pair of infrared transmitter and the receiver tube, the infrared emitting tube to emit a certain frequency, encounters an obstacle detection direction (reflecting surface), infrared reflected

DHT22 Humidity Sensor

Robokorda — Mon, 05 Sep 2022 07:56:02 +0000

MR-S-1007
Color: White
Infrared Sensor with Control Circuit Board
The Sensitivity and Holding Time Can be Adjusted
Working Voltage Range: DC 4.5V- 20V
Current Drain: <60uA Detection Range: <140° DHT11 is a Humidity and Temperature Sensor, which generates calibrated digital output. DHT11 can be interface with any microcontroller like Arduino, Raspberry Pi, etc. and get instantaneous results.

MQ-2 GAS SENSOR Module

Robokorda — Mon, 05 Sep 2022 07:49:40 +0000

MR-S-1006
Power Supply: 5 Volts
Interface Type: Analog & Digital
High Sensitivity to Smoke & combustible gasses like Hydrogen, LPG & Propane.
Low Cost.
Stable & Long Life.
On board Power indication.

It is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. It requires no external components just plug in Vcc & ground pins and you are ready to go.